Whatever I do, the device does not do things in the network. Once I plug it into power, the green light flashes for a while, then it changes to orange/amber in the same rhythm.
Hopefully other affected customers will find this earlier. I am posting here because it took much longer than needed to find the "solution". Linux telephony interface: v1.I bought a Dockstar earlier today and had no success getting it to work. mice: PS/2 mouse device common for all mice
usbcore: registered new interface driver usb-storage scsi0 : SCSI emulation for USB Mass Storage devices drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver usbcore: registered new interface driver usblp usb 1-1.2: configuration #1 chosen from 1 choice usb 1-1.2: new high speed USB device using ehci_marvell and address 3 usb 1-1: configuration #1 chosen from 1 choice usb 1-1: new high speed USB device using ehci_marvell and address 2 USB Universal Host Controller Interface driver v3.0 usb usb1: configuration #1 chosen from 1 choice ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 ehci_marvell ehci_marvell.70059: Marvell Orion EHCI Creating 4 MTD partitions on "nand_mtd": NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit) NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ e100: Copyright(c) 1999-2006 Intel Corporation Copyright (c) 1999-2006 Intel Corporation. Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI o Network Fast Processing (Routing) supported o Single TX Queue support - ETH_DEF_TXQ=0 o Single RX Queue support - ETH_DEF_RXQ=0 RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled io scheduler anticipatory registered (default) squashfs: version 3.3 (1) Phillip Lougher Use the XOR engines (acceleration) for enhancing the following functions: TCP: Hash tables configured (established 4096 bind 4096) TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes) IP route cache hash table entries: 1024 (order: 0, 4096 bytes) Time: kw_clocksource clocksource has been installed. usbcore: registered new device driver usb usbcore: registered new interface driver hub usbcore: registered new interface driver usbfs PCI: bus0: Fast back to back transfers enabled Marvell USB EHCI Host controller #0: c0537600 Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)- SHEEVA PLUG Soc: 88F6281 A0 LE
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) PID hash table entries: 512 (order: 9, 2048 bytes) Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets Memory policy: ECC disabled, Data cache writeback Using UBoot passing parameters structure Image Type: ARM Linux Kernel Image (uncompressed) Reading data from 0x3ff800 - 100% complete. Mem malloc Initialization (8M - 7M): Done U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60ĭRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6Īddresses 8M - 0M are saved for the U-Boot usage. So when you now boot up the device, you'll get the following output in the terminal: Start your terminal client (Linux: minicom), and don't forget to disable Hardware Flow Control in minicom!!.Connect the Freeagent to your DHCP router, but don't connect it to the internet! The Freeagent shall receive an IP address, but it shall not be able to phone home!.For this purpose you use an Arduino style level shifter with 3,3V which you connect to the pins 6, 4, 2:
First you need to connecto to the serial port.